Hyundai Venue (QX): Steering System / Specifications

Hyundai Venue (QX) (2020-2026) Service Manual / Steering System / Specifications

Specifications
Item
Specification
Type
 Electric Power Steering System
Steering gear
 Type
 Rack & Pinion
Rack stroke
 150 mm (5.90 in.) ± 1 (0.3937 in)
Steering angle (Max.)
 Inner
 38.9° (+0.5° / -1.5°)
Outer
 32.6°

Tightening Torques
Item
Tightening torque (kgf.m)
N.m
kgf.m
lb-ft
Hub nuts
 107.9 - 127.5
 11.0 - 13.0
 79.6 - 94.0
Steering wheel lock bolt
 44.1 - 49.0
 4.5 - 5.0
 32.5 - 36.2
Steering column mounting
Bolt
 53.9 - 58.8
 5.5 - 6.0
 39.8 - 43.4
Nuts
 25.0 - 29.4
 2.5 - 3.0
 14.5 - 21.7
teering column to Universal joint (M8 BOLT)
32.4 - 38.3
 3.3 - 3.8
 23.9 - 27.5
Steering column to Universal joint (M10 BOLT)
49.0 - 58.8
5.0 - 6.0
36.2 - 43.4
Bolt connecting universal joint to pinion
32.4 - 38.3
 3.3 - 3.8
 23.9 - 27.5
Tie rod end castle nut
24.5 - 34.3
 2.5 - 3.5
 18.1 - 25.3
Lower arm to front axle
58.8 - 70.6
 6.0 - 7.2
 43.4 - 52.1
Steering gear box to sub frame
88.3 - 107.9
 9.0 - 11.0
 65.1 - 79.6
Stabilizer link nut
98.1 - 117.7
 10.0 - 12.0
 72.3 - 86.8
Sub frame mounting bolts & nuts
156.9 - 176.5
 16.0 - 18.0
 115.7 - 130.2

    Troubleshooting Trouble Symptom Cause of the symptom Remedy Excessive play in steering Loose U-joint bolt Retighten or replace as necessary Loose yoke plug Retighten Loose steering gear mounting bolts Retighten Loose or worn tie rod end Retighten or replace as necessary Steering wheel does not return to its original position Excessive turning resistance of tie rod end Replace Yoke plug excessively tight Adjust Tie rod and / or ball joint cannot turn smoothly Replace Loose mounting of gear box at the subframe Retighten Worn steering shaft joint and/or body grommet Correct or replace Distorted rack Replace Rattling or chucking noise in the rack and pinion Loose steering gear box mounting Reposition Loose tie rod end and/or ball joint Repace Worn tie rod and/or ball joint Repace Loose yoke plug Replace

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Photo Sensor. Description and operation

    Description The photo sensor is located at the center of the defrost nozzles. The photo sensor contains a photovoltaic (sensitive to sunlight) diode. The solar radiation received by its light receiving portion, generates an electromotive force in proportion to the amount of radiation received which is transferred to th

    Hyundai Venue (QX) (2020-2026) Service Manual: Rear Corner Radar Unit. Repair procedures

    Removal    lf replacement of the rear corner radar unit bracket or extension wire is required, replace the defective part only with a new one. 1.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0189