Hyundai Venue (QX): Lubrication System / Engine Oil. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Engine Mechanical System / Lubrication System / Engine Oil. Repair procedures

Replacement
Hyundai Venue. Engine Oil. Repair procedures   
•
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
•
Exercise caution in order to minimize the length and frequency of contact of your skin to used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents.
•
In order to preserve the environment, used oil and used oil filter must be disposed of only at designated disposal sites.
1.
Drain the engine oil.
(1)
Remove the oil filler cap.
(2)
Remove the oil drain plug, and drain the oil into a container.
2.
Remove the oil filter (A) with the SST (09263-2E000, the oil filter wrench).
(1)
Remove the oil filter.
(2)
Check and clean the oil filter installation surface.
(3)
Check the part number of the new oil filter is as same as old one.
(4)
Apply clean engine oil to the gasket of a new oil filter.
(5)
Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.
(6)
Tighten it with the torque below.
Tightening torque :
11.8 - 15.7 N.m (1.2 - 1.6 kgf.m, 8.7 - 11.6 lb-ft)

Hyundai Venue. Engine Oil. Repair procedures
3.
Refill with engine oil.
(1)
Clean and install the oil drain plug with a new gasket.
Tightening torque :
34.3 - 44.1 N.m (3.5 - 4.5 kgf.m, 25.3 - 32.5 lb-ft)
(2)
Fill with fresh engine oil.
Capacity
Total : 3.7 - 4.0L (3.90 - 4.22 US qt, 3.25 - 3.51 lmp qt, 0.97 - 1.05 US gal)
Oil pan : 3.3L (3.48US qt, 2.90lmp qt, 0.87 US gal)
Drain and refill in cluding oil filter :
3.6 L (3.80US qt, 3.16lmp qt, 0.95 US gal)
(3)
Install the oil filler cap.
4.
Start engine and check for oil leaks.
5.
Recheck the engine oil level.
Inspection
Engine Oil
1.
Check the engine oil quality.
Check the oil deterioration, entry of water, discoloring of thinning.
If the quality is visibly poor, replace the oil.
2.
Check the engine oil level.
After warning up the engine and then 5 minutes after the engine stop, oil level should be between the "L" and "F" marks in the dipstick.
If low, check for leakage and add oil up to the "F" mark.
Hyundai Venue. Engine Oil. Repair procedures   
•
Do not fill with engine oil above the "F" mark.
Selection of Engine Oil
Specification
For all except Middle East :
API SM & ILSAC GF-4 or above / 5W-20
ACEA A5 or above / 5W-20
For Middle East :
ACEA A5 or above / 5W-30
Hyundai Venue. Engine Oil. Repair procedures   
•
API SL, ILSAC GF-3, ACEA A3 Class engine oil can be used if the recommended engine oil is not available.
SAE viscosity grade
Refer to the recommended SAE viscosity number.

Hyundai Venue. Engine Oil. Repair procedures

Hyundai Venue. Engine Oil. Repair procedures   
•
For best performance and maximum protection of all types of operation, select only those lubricants which :
1)
Satisfy the requirement of the API, ILSAC or ACEA classification.
2)
Have proper SAE grade number for expected ambient temperature range.
3)
Lubricants that do not have both an SAE grade number and API, ILSAC or ACEA service classification on the container should not be used.

    Removal and Installation 1. Disconnect the battery negative terminal. 2. Remove the engine room under cover.

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Temperature Control Actuator. Description and operation

    Description The temperature control actuator is located at the heater unit. It regulates the temperature by the procedure as follows. The signal from the control unit adjusts the position of the temperature door by operating the temperature switch.

    Hyundai Venue (QX) (2020-2026) Service Manual: Special service tools

    Special Service Tools Tool Name / Number Illustration Description LKA Compensator (09890-3V100) Used for compensating front view camera unit BCW Sensor Correction Tool Set (09958-3T500) Used to correct the blin

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0111