Hyundai Venue (QX): Rear Seat / Rear Seat Back Cover. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Body (Interior and Exterior) / Rear Seat / Rear Seat Back Cover. Repair procedures

Replacement

[LH]

•	Put on gloves to prevent hand injuries.

•	When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

1.	Remove the rear seat assembly [RH]. (Refer to Rear Seat - "Rear Seat Assembly")

2.	Push the lock pins, and remove the rear seat headrest (A).

3.	Loosen the mounting screw and remove the rear seat folding cover (A).

4.	Using a remover and remove the rear seat back latch cover (A).

5.	Remove the protector (A).

6.	Zip off the rear seat back cover (A), and then pull it up. [RH] [LH]

7.	Using a remover and remove the cap (A).

8.	Separate the hog-ring clips, protector (A) and remove the rear seat back board (B).

9.	Pull out the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.

10.	Remove the rear seat back frame (A).

11.	After removing the hog-ring clips (A) inside the rear seat back cover, remove the seat back cover (B).

12.

To install, reverse removal procedure.

•	Make sure that the connectors are connected completely.

•	Replace any damaged clips (or pin-type retainers).

•	To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).

•	Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

Hyundai Venue. Rear Seat Back Cover. Repair procedures

[RH]

•	Put on gloves to prevent hand injuries.

•	When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

1.	Remove the rear seat assembly [LH]. (Refer to Rear Seat - "Rear Seat Assembly")

2.	Push the lock pins, and remove the rear seat headrest (A).

3.	Loosen the mounting screw and remove the rear seat folding cover (A).

4.	Using a remover and remove the rear center seat belt cover (A).

5.	Using a remover and remove the rear seat back latch cover (A).

6.	Remove the protector (A).

7.	Zip off the rear seat back cover (A), and then pull it up. [RH] [LH]

8.	Separate the hog-ring clips, protector (A) and remove the rear seat back board (B).

9.	Using a remover and remove the cap (A).

10.	Pull out the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.

11.	Remove the rear seat back frame (A).

12.	After removing the hog-ring clips (A) inside the rear seat back cover, remove the seat back cover (B).

13.

To install, reverse removal procedure.

•	Make sure that the connectors are connected completely.

•	Replace any damaged clips (or pin-type retainers).

•	To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).

•	Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

Hyundai Venue. Rear Seat Back Cover. Repair procedures

❮Rear Seat Back Cover. Components and components location

Component Location 1. Rear seat back cover [LH] 2. Rear seat back cover [RH]

Rear Seat Cushion Cover. Components and components location❯

Component Location 1. Rear seat cushion cover

Other information:

Hyundai Venue (QX) (2020-2026) Service Manual: PTC Heater. Repair procedures

Inspection Operating Logic Test (Manual only) Inspect the PTC operation by confirmation logic as follows; 1. Entering (1) Set the Floor mode and maximum heating position. (2) Turn off the blower switch.

Hyundai Venue (QX): Rear Seat / Rear Seat Back Cover. Repair procedures

Other information:

Hyundai Venue (QX) (2020-2026) Service Manual: PTC Heater. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual: Heater & A/C Control Unit (Manual). Components and components location

Categories