Hyundai Venue (QX): Rear Hub - Carrier / Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Driveshaft and axle / Rear Hub - Carrier / Repair procedures

Removal
[Rear drum brake type]
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from the rear hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
Hyundai Venue. Repair procedures   
•
Be careful not to damage the hub bolts when removing the rear wheel and tire (A).

Hyundai Venue. Repair procedures
3.
Loosen the screw and then remove the rear drum brake (A).
Tightening torque :
4.9 - 5.9 N.m (0.5 - 0.6 kgf.m, 3.6 - 4.3 lb-ft)

Hyundai Venue. Repair procedures
4.
Remove the upper shoe return spring (A).

Hyundai Venue. Repair procedures
5.
Remove the lower shoe return spring (A).

Hyundai Venue. Repair procedures
6.
Remove the adjster spring (A).

Hyundai Venue. Repair procedures
7.
Remove the shoe holder (A) and then remove the rining.

Hyundai Venue. Repair procedures
8.
Disconnect the parking brake cable (A) from lining (B).

Hyundai Venue. Repair procedures
9.
Remove the clip (A).

Hyundai Venue. Repair procedures
10.
Loosen the brake flare nut (A).
Tightening torque :
12.7 - 16.7 N.m (1.3 - 1.7 kgf.m, 9.4 - 12.3 lb-ft)

Hyundai Venue. Repair procedures
11.
Loosen the hub mounting bolts and then remove the hub (A) from the torsion beam.
Tightening torque :
49.0 - 58.8 N.m (5.0 - 6.0 kgf.m, 36.2 - 43.4 lb-ft)

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures   
•
Do not hammer on the hub bearing to remove it; it may damage the guide pin.
•
Be careful not to damage to the dust cover when removing hub bearing.
[Rear disc brake type]
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from the rear hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
Hyundai Venue. Repair procedures   
•
Be careful not to damage the hub bolts when removing the rear wheel and tire (A).

Hyundai Venue. Repair procedures
3.
Remove the rear brake caliper.
(Refer to Brake System - "Rear Disc Brake")
4.
Loosen the screws and then remove the rear brake disc (A).
Tightening torque :
4.9 - 5.9 N.m (0.5 - 0.6 kgf.m, 3.6 - 4.3 lb-ft)

Hyundai Venue. Repair procedures
5.
Disconnect the rear wheel speed sensor connector (A).

Hyundai Venue. Repair procedures
6.
Remove the hub bearing assembly (A).
Tightening torque :
49.0 - 58.8 N.m (5.0 - 6.0 kgf.m, 36.2 - 43.4 lb-ft)

Hyundai Venue. Repair procedures
7.
Loosen the mounting bolts and then separate the extra bracket from the backing plate.
Tightening torque :
2.0 - 2.9 N.m (0.2 - 0.3 kgf.m, 1.4 - 2.2 lb-ft)

Hyundai Venue. Repair procedures
Inspection
1.
Check the hub for cracks and the splines for wear.
2.
Check the brake disc for scoring and damage.
3.
Check the rear axle carrier for cracks.
4.
Check the bearing for cracks or damage.
Installation
1.
Install in the reverse order of removal.
2.
After installation, bleed the brake system.
(Refer to Brake System - "Brake system bleeding")
(Refer to Brake System - "ABS system bleeding")

    Components [Rear drum brake type] 1. Brake assembly 2. Rear hub assembly 3. Rear drum [Rear disc brake type] 1.

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Troubleshooting

    Troubleshooting Problem Symptoms Table Before replacing or repairing air conditioning components, first determine if the malfunction is due to the refrigerant charge, air flow or compressor. Use the table below to help you find the cause of the problem.

    Hyundai Venue (QX) (2020-2026) Service Manual: Cruise Control (CC) Switch. Components and components location

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0148