Hyundai Venue (QX): Roof Trim / Roof Trim Assembly. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Body (Interior and Exterior) / Roof Trim / Roof Trim Assembly. Repair procedures

Replacement
Hyundai Venue. Roof Trim Assembly. Repair procedures   
•
Put on gloves to prevent hand injuries.
•
When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
•
Use a plastic panel removal tool to remove interior trim pieces without marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the front seat.
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the rear seat.
(Refer to Rear Seat - "Rear Seat Assembly")
3.
Remove the front pillar trim.
(Rear to Interior Trim - "Front Pillar Trim")
4.
Remove the center pillar lower trim.
(Rear to Interior Trim - "Center Pillar Trim")
5.
Remove the center pillar upper trim.
(Rear to Interior Trim - "Center Pillar Trim")
6.
Remove the rear pillar trim.
(Rear to Interior Trim - "Rear Pillar Trim")
7.
Remove the sunvisor and retainer.
(Rear to Roof Trim - "Sunvisor")
8.
Remove the assist handle.
(Rear to Roof Trim - "Assist Handle")
9.
Remove the overhead console lamp.
(Rear to Body Electrical System - "Overhead Console Lamp")
10.
Remove the room lamp.
(Rear to Body Electrical System - "Room Lamp")
11.
Remove the tailgate weatherstrip.
(Refer to Tailgate - "Tailgate Weatherstrip")
12.
Separate the roof trim main connector (A) and the mounting clips in the front pillar.

Hyundai Venue. Roof Trim Assembly. Repair procedures
13.
Remove the roof trim mounting clip and remove the roof trim assembly (A).

Hyundai Venue. Roof Trim Assembly. Repair procedures
14.
Press the lock pin and separate the sunroof motor connector (A).

Hyundai Venue. Roof Trim Assembly. Repair procedures
15.
Remove the roof trim assembly (A) from the vehicle through the tailgate.
Hyundai Venue. Roof Trim Assembly. Repair procedures   
•
Be careful not to wrinkle on the roof trim.

Hyundai Venue. Roof Trim Assembly. Repair procedures
16.
Remove roof trim wiring harness from the roof trim.
Hyundai Venue. Roof Trim Assembly. Repair procedures   
•
Take care not to damage the roof trim wiring harness (A) when removing.

Hyundai Venue. Roof Trim Assembly. Repair procedures

Hyundai Venue. Roof Trim Assembly. Repair procedures   
1)
When installing the roof trim wiring harness (A) on the roof trim, apply the hot melt continuously by using the hot melt gun tool.
2)
Put anti-noise pad on roof trim to prevent the noise.
17.
To install, reverse removal procedure.
Hyundai Venue. Roof Trim Assembly. Repair procedures   
•
Make sure the connector is connected properly.
•
Replace any damaged clips (or pin-type retainers).

    Component Location 1. Roof Trim Assembly

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Compressor. Description and operation

    Description The compressor is the power unit of the A/C system. It is located on the side of engine block and driven by a V-belt of the engine. The compressor changes low pressure and low temperature refrigerant gas into high pressure and high temperature refrigerant gas.

    Hyundai Venue (QX) (2020-2026) Service Manual: Ambient Temperature Sensor. Description and operation

    Description The ambient temperature sensor is located at the front of the condenser and detects ambient air temperature. It is a negative type thermistor; resistance will increase with lower temperature, and decrease with higher temperature.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0143