| Specification |
|
Engine |
Tramsaxle |
Max. permissible angle |
|
|
Outer |
Inner |
||
|
Gamma 1.6 MPI |
M/T & A/T |
46.5° |
26° |
|
Gamma II 1.6 MPI |
M/T & IVT |
||
| Tightening torque |
|
Item |
N.m |
kgf.m |
lb-ft |
|
|
Front |
Hub nuts |
107.9 - 127.5 |
11.0 - 13.0 |
79.6 - 94.0 |
|
Driveshaft caulking nut |
274.6 - 294.2 |
28.0 - 30.0 |
202.5 - 217.0 |
|
|
Strut assembly to knuckle |
157.0 - 176.6 |
16.0 - 18.0 |
115.7 - 130.1 |
|
|
Front caliper to knuckle |
78.4 - 98.1 |
8.0 - 10.0 |
57.8 - 72.3 |
|
|
Wheel speed sensor mounting bolt |
7.8 - 11.8 |
0.8 - 1.2 |
5.8 - 8.7 |
|
|
Disc fixing screw |
4.9 - 5.9 |
0.5 - 0.6 |
3.6 - 4.3 |
|
|
Lower arm to knuckle |
68.6 - 80.4 |
7.0 ~ 8.2 |
50.6 - 59.3 |
|
|
Tie rod end castle nut |
34.3 - 44.1 |
3.5 ~ 4.5 |
25.3 - 32.5 |
|
|
Dust cover mounting bolt |
3.9 - 5.9 |
0.4 ~ 0.6 |
2.9 - 4.3 |
|
|
Rear |
Hub nuts |
107.9 - 127.5 |
11.0 ~ 13.0 |
79.6 - 94.0 |
|
Disc fixing screw |
4.9 - 5.9 |
0.5 - 0.6 |
3.6 - 4.3 |
|
|
Brake caliper mounting bolt |
63.7 - 73.5 |
6.5 ~ 7.5 |
47.0 - 54.2 |
|
|
Hub assembly mounting bolt |
49.0 - 58.8 |
5.0 ~ 6.0 |
36.2 - 43.4 |
|
|
| Lubricants |
|
Engine |
Tramsaxle |
Joint type |
Lubricants |
Quantity |
|
Gamma 1.6 MPI |
M/T & A/T |
BJ |
MS511-50 CVBJ-2 |
95g + 10g |
|
TJ |
MS511-50 CVTJ |
119g + 10g |
||
|
Gamma II 1.6 MPI |
M/T & IVT |
BJ |
MS511-50 CVBJ-2 |
90g + 10g |
|
TJ |
MS511-50 CVTJ |
98g + 10g |
Special Service Tools Tool(Number and Name) Illustration Use 09495-39100 Band installer Installation of hook type boot band 09495-3K000 Band installer Installation of ear type boot band 09495-33000 Puller Remove the spider assembly from the drive shaft 09568-1S100 Ball joint puller Remove the ball joint front axle
Inspection 1. Disconnect the ignition switch connector (B) and key warning switch connector (A) from under the steering column. 2. Check for continuity between the terminals. 3.