Hyundai Venue: Timing System / Crankshaft Damper Pulley. Repair procedures
1. |
Remove the drive belt.
(Refer to Timing System - "Dreve Belt")
|
2. |
Remove the engineroom under cover.
|
3. |
Remove the passenger seat RH front tire.
(Refer to Suspension System - "Wheel")
|
4. |
Remove the crankshaft pulley (A).
Tightening torque :
46.1 - 52.0 N.m (4.7 - 5.3 kgf.m, 34.0 - 38.3 lb-ft) + 38° -
42°
|
![Hyundai Venue. Crankshaft Damper Pulley. Repair procedures](images/crankshaft_damper_pulley_repair_procedures-326/287/hyundai_venue__crankshaft_damper_pulley_repair_procedures_149.gif)
There are two methods to hold the ring gear when installing
or removing the crankshaft damper pulley.
•
|
Install the SST (09231-2B100, 09231-3N100) to hold the
ring gear after removing the starter.
![Hyundai Venue. Crankshaft Damper Pulley. Repair procedures](images/crankshaft_damper_pulley_repair_procedures-326/287/hyundai_venue__crankshaft_damper_pulley_repair_procedures_151.gif)
|
•
|
Install the SST (09231-3D100) to hold the ring gear
after removing the dust cover.
|
1) |
Remove the dust cover (A) on the bottom of the ladder
frame and unfasten the two transaxle mounting bolts
(B).
![Hyundai Venue. Crankshaft Damper Pulley. Repair procedures](images/crankshaft_damper_pulley_repair_procedures-326/287/hyundai_venue__crankshaft_damper_pulley_repair_procedures_152.gif)
|
2) |
Adjust the length of the holder nuts (A) so that the
front plate of the holder (B) puts in the ring gear
(C) teeth.
|
3) |
Adjust the angle of the links (D) so that the two transaxle
mounting bolts can be fastened to the original mounted
holes.
![Hyundai Venue. Crankshaft Damper Pulley. Repair procedures](images/crankshaft_damper_pulley_repair_procedures-326/287/hyundai_venue__crankshaft_damper_pulley_repair_procedures_153.gif)
|
4) |
Install the SST (09231-3D100, 09231-2W100) using the
two transaxle mounting bolts and spacers. Tighten the
bolts and nuts of the holder and links securely.
![Hyundai Venue. Crankshaft Damper Pulley. Repair procedures](images/crankshaft_damper_pulley_repair_procedures-326/287/hyundai_venue__crankshaft_damper_pulley_repair_procedures_154.gif)
|
|
|
5. |
Installation is reverse order of removal.
When installing the pulley, the groove on the pulley should be positioned
outside.
![Hyundai Venue. Crankshaft Damper Pulley. Repair procedures](images/crankshaft_damper_pulley_repair_procedures-326/287/hyundai_venue__crankshaft_damper_pulley_repair_procedures_155.gif)
|
Other information:
..
Brake Booster Operating
Test
For simple checking of the brake booster operation, carry out the following
tests.
1.
Run the engine for one or two minutes, and then stop it. If the pedal
depresses fully the first time but gradually becomes higher when depressed
succeeding times, the booster is operating properly, if the pedal height
remains unchanged, the booster is inoperative...
Categories
![Hyundai Venue. Remote Key](images/books/1/hyundai_venue_remote_key_173.png)
Your HYUNDAI uses a remote key, which you can use to lock or unlock the driver
and passenger doors or the rear liftgate.
(1) Door Lock
(2) Door Unlock
(3) Panic
Locking Your Vehicle
To lock your vehicle:
1. Make sure all doors, the engine hood and the liftgate are closed.
read more