Hyundai Venue (QX): Front Hub / Knuckle / Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Driveshaft and axle / Front Hub / Knuckle / Repair procedures

Removal
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
Hyundai Venue. Repair procedures   
•
Be careful not to damage the hub bolts when removing the front wheel and tire (A).

Hyundai Venue. Repair procedures
3.
Remove the front brake caliper.
(Refer to Brake System - "Front Disc Brake")
4.
Loosen the screw and then remove the front disc (A).
Tightening torque :
4.9 - 5.9 N.m (0.5 - 0.6 kgf.m, 3.6 - 4.3 lb-ft)

Hyundai Venue. Repair procedures
5.
Remove the tie rod end ball joint.
(1)
Remove the split pin and nut (A).
(2)
Using SST(09568-1S100), separate the ball joint (B) from the knuckle.
Tightening torque:
34.3 - 44.1 N.m (3.5 - 4.5 kgf.m, 25.3 - 32.5 lb-ft)

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures
6.
Loosen the lower arm nut (A) and then remove the lower arm ball joint by using SST(09568-1S100).
Tightening torque :
68.6 - 80.4 N.m (7.0 - 8.2 kgf.m, 50.6 - 59.3 lb-ft)

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures
7.
Loosen the bolt and then remove the wheel speed sensor (A).
Tightening torque :
7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 5.5 - 8.7 lb-ft)

Hyundai Venue. Repair procedures
8.
Loosen the driveshaft caulking nut (A).
Tightening torque :
274.6 - 294.2 N.m (28.0 - 30.0 kgf.m, 202.5 - 217.0 lb-ft)

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures   
•
The driveshaft lock nut (A) should be replaced with new ones.
•
After installation driveshaft lock nut, stake the lock nut using a chisel and hammer as shown in the illustration below
Caulking depth : 1.5 mm (0.591 in.)

Hyundai Venue. Repair procedures
9.
Loosen the strut mounting bolts, nuts and then remove the knuckle assembly (A).
Tightening torque :
98.1 - 117.7 N.m (10.0 - 12.0 kgf.m, 72.3 - 86.8 lb-ft)

Hyundai Venue. Repair procedures
Disassembly
1.
Remove the snap ring (A).

Hyundai Venue. Repair procedures
2.
Remove the hub assembly from the knuckle assembly.
(1)
Install the front knuckle assembly (A) on press.
(2)
Lay a suitable adapter (B) upon the hub assembly shaft.
(3)
Remove the hub assembly (C) from the knuckle assembly (A) by using press.

Hyundai Venue. Repair procedures
3.
Remove the hub bearing inner race from the hub assembly.
(1)
Install a suitable tool (A) for removing the hub bearing inner race on the hub assembly.
(2)
Lay the hub assembly and tool (A) upon a suitable adapter (B).
(3)
Lay a suitable adapter (C) upon the hub assembly shaft.
(4)
Remove the hub bearing inner race (D) from the hub assembly by using press.

Hyundai Venue. Repair procedures
4.
Remove the dust cover (A).

Hyundai Venue. Repair procedures
5.
Remove the hub bearing outer race from the knuckle assembly.
(1)
Lay the hub assembly (A) upon a suitable adapter (B).
(2)
Lay a suitable adapter (C) upon the hub bearing outer race.
(3)
Remove the hub bearing outer race from the knuckle assembly by using press.

Hyundai Venue. Repair procedures
6.
Replace hub bearing with a new one.
Reassembly
1.
Install the hub bearing to the knuckle assembly.
(1)
Lay the knuckle assembly (A) on press.
(2)
Lay a new hub bearing upon the knuckle assembly (A).
(3)
Lay a suitable adapter (B) upon the hub bearing.
(4)
Install the hub bearing to the knuckle assembly by using press.

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures   
•
Do not press against the inner race of the hub bearing because that can cause damage to the bearing assembly.
•
Always use a new wheel bearing assembly.
2.
Install the dust cover (A).

Hyundai Venue. Repair procedures
3.
Install the hub assembly to the knuckle assembly.
(1)
Lay the hub assembly (A) upon a suitable adapter (B).
(2)
Lay the knuckle assembly (C) upon the hub assembly (A).
(3)
Lay a suitable adapter (D) upon the hub bearing.
(4)
Install the hub assembly (A) to the knuckle assembly (C) by using press.

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures   
•
Do not press against the inner race of the hub bearing because that can cause damage to the bearing assembly.
4.
Install the snap ring (A).

Hyundai Venue. Repair procedures
Inspection
1.
Check the hub for cracks and the splines for wear.
2.
Check the brake disc for scoring and damage.
3.
Check the knuckle for cracks.
4.
Check the bearing for cracks or damage.
Installation
1.
Install in the reverse order of removal.
2.
Check the alignment.
(Refer to Suspension System - "Alingment")

    Components 1. Brake disc 2. Front hub 3. Dust cover 4. Front axle 5. Hub bearing 6. Snap ring

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Intake Actuator. Components and components location

    Hyundai Venue (QX) (2020-2026) Service Manual: Description and operation

    Description The cruise control system is engaged by the cruise "ON/OFF" main switch located on right of steering wheel column. The system has the capability to cruise, coast, accelerate and resume speed. It also has a safety interrupt, engaged upon depressing brake or shifting select lever.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0127