Hyundai Venue (QX): Rear Corner Radar System / Rear Corner Radar Unit. Repair procedures

Hyundai Venue (QX) (2020-2025) Service Manual / Advanced Driver Assistance System (ADAS) / Rear Corner Radar System / Rear Corner Radar Unit. Repair procedures

Removal

lf replacement of the rear corner radar unit bracket or extension wire is required, replace the defective part only with a new one.

1.	Disconnect the negative (-) battery terminal.

2.	Remove the rear bumper assembly. (Refer to Body - "Rear Bumper Assembly")

Remove the rear corner radar unit (A) by loosening the nuts.

Be careful not to damage the bracket when removing the rear corner radar unit.

[Left]

Hyundai Venue. Rear Corner Radar Unit. Repair procedures

[Right]

Hyundai Venue. Rear Corner Radar Unit. Repair procedures

4.	If the bracket is physically deformed or damaged, replace the extension wire or bracket front the radar unit (A).

Installation

Install the blind spot radar unit and bracket.

Tightening torque :

bracket : 3.9 - 5.9 N

unit : 3.92 ± 0.105 N.m

2.	Install the rear bumper.

Connect the negative (-) battery terminal.

•	Take care not to confuse left side (master) and right side (slave) unit when installing.

•	BCW units connector connect to the wiring connector.

4.	Perform "Correcting the Blind-Spot Radar Unit Angle" procedures.

5.	Perform "BSD Radar Calibration" procedures.

Inspection

Correcting the Blind-Spot Radar Unit Angle

After replacing the blind-spot radar unit or bracket, with the bumper removed, use the blind-spot radar unit correction tool set (special tool : 09985-3T500) to perform angle correction.

•	Perform the task on a level place.

•	Perform the task after checking the tire pressure.

•	For the dealer who purchased the existing blind-spot radar correction tool set (09958-3T000), refer to the instructions of the 17MY shop manual and repair it.

2.	Attach a vertical plumb (special tool : 09958-3T010) on the hood, and lower the plumb (A) to the ground so that it passes through the center of the emblem.

3.	Marking the center point below the plumb (A).

4.	Attach a vertical plumb (special tool : 09958-3T010) on the trunk (or tailgate), and lower the plumb (A) to the ground so that it passes through the center of the emblem.

5.	Marking the center point below the plumb (A).

Marking the center of vehicle by a string.

1)	Pass the string through the bottom of the vehicle from the rear of the vehicle to the front and fix the string to the center point (A) of the front of the vehicle.

2)	Fix the string to the point (C) about 1.5 - 2m from the back of the vehicle so that it passes the rear center point (B).

Hyundai Venue. Rear Corner Radar Unit. Repair procedures

Mount the blind-spot radar unit fixing adaptor (special tool : 09958-3T080) on the blind-spot radar unit and fix the level laser (special tool : 09958-3T070).

Hyundai Venue. Rear Corner Radar Unit. Repair procedures

•	When with the blind-spot radar unit cover, remove the cover and then mount the fixing adapter (special tool: 09958-3T080).

Measure the angle (C) between the center line (A) of the angle measuring plate and the horizontal laser beam (B) using a digital protractor (special tool : 09958-3T090).

Horizontal Angle (C) : 37° ± 3°

Hyundai Venue. Rear Corner Radar Unit. Repair procedures

Use a digital inclinometer (special tool : 09958-3T100) to measure the vertical angle of the blind-spot radar unit.

Vertical Angle : 90° ± 1.5°

Hyundai Venue. Rear Corner Radar Unit. Repair procedures

10.

Measure the horizontal and vertical angles of left and right blind-spot radar units. If the measured values deviate from the specified values, insert a washer between the bracket of the blind-spot radar unit.

Specified Values

Horizontal Angle : 54° ± 3°

Vertical Angle : 87° ± 1.5°

Hyundai Venue. Rear Corner Radar Unit. Repair procedures

11.	After checking and correcting the blind-spot radar unit angle, perform the blind-spot radar radar correction procedure.

Diagnosis with Diagnostic tool

1.	Rear bumper accident vehicles and vehicles that replaced BCW units must perform BCW unit alignment using Diagnostic tool.

2.	Connect the cable of Diagnostic tool to the data link connector in driver side crash pad lower panel, and turn on the Diagnostic tool.

3.	Select the 'S/W Management' and 'Car model'.

4.	Select "Blind -Spot Collision Warning" and "BSD Radar Calibration".

5.	Perform the "BSD Radar Calibration" procedure according to the Diagnostic tool screen message.

❮Rear Corner Radar Unit. Schematic diagrams

Connector and Terminal Function [Connector A] Pin NO Function 1 IGN1 2 L-CAN High 3 C-CAN Low 4 Warning indicator[LH] 5 - 6 L-CAN Low 7 C-CAN High 8 Ground [Connector B] Pin NO Function 1 IGN1 2 L-CAN High 3 C-CAN Low 4 Warning indicator[LH] 5 - 6 L-CAN Low 7 C-CAN High 8 Ground Circuit Diagram

Warning Indicator. Components and components location❯

Inspection 1. Disconnect the negative (-) battery terminal. 2. Remove the front door trim.

Other information:

Hyundai Venue (QX) (2020-2025) Service Manual: Mode Control Actuator. Repair procedures

Inspection 1. Turn the ignition switch OFF. 2. Disconnect the mode control actuator connector. 3. Verify that the mode control actuator operates to the defrost mode when connecting 12V to terminal 3 and grounding terminal 4.

Hyundai Venue (QX): Rear Corner Radar System / Rear Corner Radar Unit. Repair procedures

Other information:

Hyundai Venue (QX) (2020-2025) Service Manual: Mode Control Actuator. Repair procedures

Hyundai Venue (QX) (2020-2025) Service Manual: Components and components location

Categories