Hyundai Venue (QX): Brake Pad / Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Brake System / Brake Pad / Repair procedures

Replacement
[Front Brake Pad]
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub.
Hyundai Venue. Repair procedures   
•
Be careful not to damage the hub bolts when removing the front wheel and tire (A).

Hyundai Venue. Repair procedures
3.
Up the caliper body (A) by loosening the guided rod bolt.

Hyundai Venue. Repair procedures
4.
Remove the brake pad (A).

Hyundai Venue. Repair procedures
5.
Replace the pad liner (A) with a new one.

Hyundai Venue. Repair procedures
6.
Replace the brake pad (A) with a new one.

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures   
•
When installing, use a new one brake pad (A), pad liner (B), inner shim (C).

Hyundai Venue. Repair procedures
7.
Use a SST (09581-11000) when installing the brake caliper assembly.

Hyundai Venue. Repair procedures
8.
Install the caliper body (A) then tighten the guide rod bolt.
Tightening torque :
37.3 - 41.2 N.m (3.8 - 4.2 kgf.m, 27.5 - 30.4 lb-ft)

Hyundai Venue. Repair procedures
9.
Install the front wheel and tire (A).
Tightening torque :
107.8 - 127.4 N.m (11.0 - 13.0 kgf.m, 79.5 - 94.0 lb-ft)
Hyundai Venue. Repair procedures   
•
Be careful not to damage the hub bolts when installing the front wheel and tire (A).

Hyundai Venue. Repair procedures
[Rear Brake Pad]
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from rear hub.
Hyundai Venue. Repair procedures   
•
Be careful not to damage the hub bolts when removing the rear wheel and tire (A).

Hyundai Venue. Repair procedures
3.
Disconnect the parking cable (B) after remove the parking brake cable fixing clip (A).

Hyundai Venue. Repair procedures
4.
Up the caliper body (A) by loosening the guided rod bolt.

Hyundai Venue. Repair procedures
5.
Remove the pad return spring (A).

Hyundai Venue. Repair procedures
6.
Remove the brake pad (A).

Hyundai Venue. Repair procedures
7.
Replace the pad pad liner (A) with a new one.

Hyundai Venue. Repair procedures
8.
Replace the brake pad (A) with a new one.

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures   
•
When installing, use a new one brake pad (A), pad liner (B), inner shim (C).

Hyundai Venue. Repair procedures
9.
Remove the pad return spring (A).

Hyundai Venue. Repair procedures

Hyundai Venue. Repair procedures   
•
Pad return springs must be replaced with new ones whenever pads are replaced.
•
Technicians should be careful not to deform pad return springs.
•
When pad return springs are deformed, it may cause improper braking, more fuel consumption.
10.
When installing, press and rotate the piston into the caliper body until it is fully retracted.

Hyundai Venue. Repair procedures
11.
Install the caliper body (A) then tighten the guide rod bolt.
Tightening torque :
37.3 - 41.2 N.m (3.8 - 4.2 kgf.m, 27.5 - 30.4 lb-ft)

Hyundai Venue. Repair procedures
12.
Install the parking brake cable (B) and than fixing the clip (A).

Hyundai Venue. Repair procedures
13.
Install the rear wheel and tire (A).
Tightening torque :
107.8 - 127.4 N.m (11.0 - 13.0 kgf.m, 79.5 - 94.0 lb-ft)
Hyundai Venue. Repair procedures   
•
Be careful not to damage the hub bolts when installing the rear wheel and tire (A).

Hyundai Venue. Repair procedures
Inspection
Front Brake Pad Check
1.
Check the pad wear. Measure the pad thickness and replace it, if it is less than the specified value.
Front brake disc thickness Pad thickness
- Standard : 11.0 mm (0.43 in)
- Service Limit : 2.0 mm (0.78 in)

Hyundai Venue. Repair procedures
2.
Check that grease is applied, to sliding contact points and the pad and backing metal for damage.
Rear Brake Pad Check
1.
Check the pad wear. Measure the pad thickness and replace it, if it is less than the specified value.
Pad thickness
- Standard value : 10.0 mm (0.39 in)
- Service limit : 2.0 mm (0.0787 in)
2.
Check the damage of pad, backing metal and contamination with grease.

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Heater Unit. Components and components location

    Component Location 1. Heater unit assembly Compoents 1. Mode control actuator 2. Heater core case 3. Center duct seal 4. PTC heater 5. Heater core assembly 6. Heater case [LH] 7.

    Hyundai Venue (QX) (2020-2026) Service Manual: Temperature Control Actuator. Description and operation

    Description The temperature control actuator is located at the heater unit. It regulates the temperature by the procedure as follows. The signal from the control unit adjusts the position of the temperature door by operating the temperature switch.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0139