Hyundai Venue (QX): SRSCM / SRS Control Module (SRSCM). Repair procedures

Hyundai Venue (QX) (2020-2025) Service Manual / Restraint / SRSCM / SRS Control Module (SRSCM). Repair procedures

Removal
1.
Remove the ignition key from the vehicle.
2.
Disconnect the battery negative cable and wait for at least three minutes before beginning work.
3.
Remove the floor console.
(Refer to Body - "Floor Console Assembly")
4.
Remove the air duct (A).

Hyundai Venue. SRS Control Module (SRSCM). Repair procedures
5.
Disconnect the SRSCM connectors.

Hyundai Venue. SRS Control Module (SRSCM). Repair procedures
6.
Remove the SRSCM (A) after loosening the mounting nuts.

Hyundai Venue. SRS Control Module (SRSCM). Repair procedures
Installation
1.
Remove the ignition key from the vehicle.
2.
Disconnect the battery negative cable and wait for at least three minutes before beginning work.
3.
Install the SRSCM (A) with the SRSCM mounting nuts.
Tightening torque :
7.0 - 7.7 N.m (0.7 - 0.8 kgf.m, 5.1 - 5.6 Ib-ft)

Hyundai Venue. SRS Control Module (SRSCM). Repair procedures
4.
Connect the SRSCM harness connectors.
5.
Install the heater ducts and floor console.
(Refer to Body - "Floor Console Assembly")
6.
Reconnect the battery negative cable.
7.
After installing the SRSCM, confirm proper system operation :
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
Variant Coding
1.
Connect the cable of GDS to the data link connector in driver side crash pad lower panel, and turn on the GDS.
2.
Select the 'S/W Management' and 'Car model'.

Hyundai Venue. SRS Control Module (SRSCM). Repair procedures
3.
Select "Airbag" and "ACU/SRSCM Variant Coding".

Hyundai Venue. SRS Control Module (SRSCM). Repair procedures
4.
Perform the "ACU/SRSCM Variant Coding" procedure according to the GDS screen message.

Hyundai Venue. SRS Control Module (SRSCM). Repair procedures

    Components 1. Supplemental Restraint System Control Module (SRSCM) Supplemental Restraint System Control Module (SRSCM) No Connector A Connector B 1 Driver airbag 2st stage High (+) - 2 Driver airbag 2st stage Low (+) - 3 Passenger airbag 2st stage Low (+) - 4 Passenger airbag 2st stage High (+) - 5 - - 6 - - 7 - - 8 - Retractor pretensioner-Rear, passenger HIGH (+) 9 - Retractor pretensioner-Rear, passenger LOW (-) 10 Battery (+) - 11 Crash Output - 12 Passenger Airbag 1st Stage LOW (-) - 13 Passenger Airbag 1st Stage HIGH (+) - 14 - - 15 - - 16 Passenger airbag OFF lamp/Telltale lamp - 17 Passenger airbag ON lamp Curtain Airbag Passenger LOW (-) 18 Curtain Airbag Passenger HIGH (+) 19 Driver Airbag 1st HIGH (+) Curtain Airbag Driver HIGH (+) 20 Driver Airbag 1st LOW (-) Curtain Airbag Driver LOW (-) 21 - Side Airbag Front Passenger LOW (-) 22 - Side Airbag Front Passenger HIGH (+) 23 - Side Airbag Front Driver HIGH (+) 24 - Side Airbag Front Driver LOW (-) 25 - Adaptive load limiter, passenger LOW (-) 26 C-CAN LOW (-) Adaptive load limiter, passenger HIGH (+) 27 C-CAN HIGH (+) Retractor Pretensioner Front Driver LOW (-) 28 IGN 1 Retractor Pretensioner Front Driver HIGH (+) 29 Front Impact Sensor Driver_ HIGH (+) - 30 Front Impact Sensor_Driver LOW (-) - 31 Front Impact Sensor_Passenger LOW (-) - 32 Front Impact Sensor_Passenger HIGH (+) Retractor Pretensioner Front Passenger HIGH (+) 33 Passenger airbag On/Off switch HIGH (+) Retractor Pretensioner Front Passenger LOW (-) 34 Passenger airbag On/Off switch LOW (-) - 35 L-CAN LOW (-) - 36 L-CAN HIGH (+) - 37 - 38 Adaptive load limiter, driver LOW (-) 39 Adaptive load limiter, driver HIGH (+) 40 Ground 41 - 42 - 43 - 44 - 45 - 46 - 47 Side Impact Sensor Front Driver HIGH (+) 48 Side Impact Sensor Front Driver LOW (-) 49 Side Impact Sensor Front Passenger LOW (-) 50 Side Impact Sensor Front Passenger HIGH (+) 51 - 52 -

    Description • The front impact sensor (FIS) is installed on the upper of the side panel in Front End Module (FEM).

    Other information:

    Hyundai Venue (QX) (2020-2025) Service Manual: Temperature Control Actuator. Repair procedures

    Inspection 1. Turn the ignition switch OFF. 2. Disconnect the temperature control actuator connector. 3. Verify that the temperature control actuator operates to the cool position when connecting 12V to terminal 3 and grounding terminal 7.

    Hyundai Venue (QX) (2020-2025) Service Manual: Description and operation

    Description and Operation Blcok Diagram    • This system monitors the driving situations through the radar and the camera. Thus, for a situation out of the sensing range, the system may not normally operate.

    Categories

     
    Copyright © 2025 www.hvenueqx.com - 0.0096