Hyundai Venue (QX): Front Suspension System / Front Stabilizer Bar. Repair procedures

Hyundai Venue (QX) (2020-2025) Service Manual / Suspension System / Front Suspension System / Front Stabilizer Bar. Repair procedures

Removal
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
Hyundai Venue. Front Stabilizer Bar. Repair procedures   
•
Be careful not to damage the hub bolts when removing the front wheel and tire (A).

Hyundai Venue. Front Stabilizer Bar. Repair procedures
3.
Disconnect the stabilizer link with the front strut assembly after loosening the nut (A).
Tightening torque :
98.1 - 117.7 N.m (10.0 - 12.0 kgf.m, 72.3 - 86.8 lb-ft)
Hyundai Venue. Front Stabilizer Bar. Repair procedures   
•
When loosening the nut (A), fix the outer hexagon of stabilizer bar link.
•
Be careful not to damage the stabilizer link boots.

Hyundai Venue. Front Stabilizer Bar. Repair procedures
4.
Remove the tie rod end ball joint.
(1)
Remove the split pin and nut (A).
(2)
Using SST(09568-1S100), separate the ball joint (B) from the knuckle.
Tightening torque :
34.3 - 44.1 N.m (3.5 - 4.5 kgf.m, 25.3 - 32.5 lb-ft)

Hyundai Venue. Front Stabilizer Bar. Repair procedures

Hyundai Venue. Front Stabilizer Bar. Repair procedures
5.
Loosen the lower arm nut (A) and then remove the lower arm ball joint by using SST(09568-1S100).
Tightening torque :
68.6 - 80.4 N.m (7.0 - 8.2 kgf.m, 50.6 - 59.3 lb-ft)

Hyundai Venue. Front Stabilizer Bar. Repair procedures

Hyundai Venue. Front Stabilizer Bar. Repair procedures
6.
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.
Tightening torque :
M8 BOLT : 32.4 - 37.3 N.m (3.3 - 3.8 kgf.m, 23.9 - 27.5 lb-ft)
M10 BOLT : 49.0 - 58.8 N.m (5.0 - 6.0 kgf.m, 36.2 - 43.4 lb-ft)

Hyundai Venue. Front Stabilizer Bar. Repair procedures

Hyundai Venue. Front Stabilizer Bar. Repair procedures   
•
The clock springs inner cable may be damaged in case the steering wheel moves. Make sure to put the steering wheel in the center position.
•
Do not reuse the bolt.
•
Lock the steering wheel in the straight ahead position to prevent the damage of the clock spring inner cable.
•
When assembling, insert the shark pin into the universal joint york slot as the below illustration.

Hyundai Venue. Front Stabilizer Bar. Repair procedures
7.
Remove the engine room under cover (A).
(Refer to Engine Mechanical System - "Engine Room Under Cover")
8.
Remove the heated protector (A).

Hyundai Venue. Front Stabilizer Bar. Repair procedures
9.
Remove the muffler rubber hanger (A).

Hyundai Venue. Front Stabilizer Bar. Repair procedures
10.
Remove the roll rod bracket (C) by loosening the bolt (A), (B).
Tightening torque
(A) : 107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
(B) : 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb-ft)

Hyundai Venue. Front Stabilizer Bar. Repair procedures
11.
Remove the subframe by loosening the mounting bolts and nuts.
Hyundai Venue. Front Stabilizer Bar. Repair procedures   
•
Set a transmission jack for safety.
Tightening torque :
176.5 - 196.1Nm (18.0 - 20.0 kgf.m, 130.2 - 144.7 lb-ft)

Hyundai Venue. Front Stabilizer Bar. Repair procedures
12.
Loosen the mounting bolts and then remove the stabilizer bar (A).
Tightening torque :
44.1 - 53.9 N.m (4.5 - 5.5 kgf.m, 32.5 - 39.8 lb-ft)

Hyundai Venue. Front Stabilizer Bar. Repair procedures
13.
Remove the stabilizer link.
Tightening torque :
98.1 - 117.7 N.m (10.0 - 12.0 kgf.m, 72.3 - 86.8 lb-ft)

Hyundai Venue. Front Stabilizer Bar. Repair procedures
14.
Remove the bushing.

Hyundai Venue. Front Stabilizer Bar. Repair procedures
Inspection
1.
Check the bushing for wear and deterioration.
2.
Check the front stabilizer bar for deformation.
3.
Check the front stabilizer link ball joint for damage.
Installation
1.
Install in the reverse order of removal.
2.
Check the alignment.
(Refer to Suspension System - "Alignment")

    Removal 1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2.

    Removal 1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2.

    Other information:

    Hyundai Venue (QX) (2020-2025) Service Manual: Ambient Temperature Sensor. Repair procedures

    Inspection 1. Check the resistance of the ambient temperature sensor between terminals 1 and 2 whether it changes by changing the ambient temperature. 1. Ambient Sensor (+) 2.

    Hyundai Venue (QX) (2020-2025) Service Manual: Warning Indicator. Repair procedures

    Inspection 1. Disconnect the negative (-) battery terminal. 2. Remove the front door trim. (Refer to Body - "Front door trim") 3. Disconnect the power door mirror connector from the harness 4.

    Categories

     
    Copyright © 2025 www.hvenueqx.com - 0.0108