| Components |

|
No |
Connector A |
Connector B |
Connector C |
Connector D |
Connector E |
|
1 |
- |
- |
- |
- |
- |
|
2 |
Rear washer Switch_Input |
- |
- |
Heated handle indicator_output |
ACC Relay_output |
|
3 |
Front washer Switch_Input |
PDW-R power_output |
ATM solenoid_output |
- |
Starter Relay_output |
|
4 |
Battery (+) Power |
Hazard Switch_input |
RH Turn signal lamp actuator_output |
NTC sensor_input |
IGN1 Relay_output |
|
5 |
- |
Sunroof Status_input |
- |
Rear left seat belt indicator_output |
ESCL (-)_output |
|
6 |
GND Power |
Autolight Switch_input |
Serial communication (K-Line) with EMS |
- |
SSB Switch2_input |
|
7 |
SBL LH_output |
Rear wiper Switch_input |
ESCL Unlock Switch_input |
GND (NTC) |
SSB Switch1_input |
|
8 |
SBL Power_input |
Front wiper volume Switch_input |
Front wiper low backup switch_input |
- |
Outside Hnadle Antenna Passenger (+)_output |
|
9 |
- |
Turn Signal Switch_input |
P position_input (AT) |
- |
Interior Antenna1 Power_output |
|
Clutch IGN Lock_input (MT) |
|||||
|
10 |
Turn Signal Power_input |
Fog Switch FR_input |
Wiper parking switch_input |
- |
Interior Antenna2 Power_output |
|
11 |
Battery (+) ECU |
Front wiper switch_input |
Brake Switch_input |
- |
Outside Hnadle Antenna Driver (+)_output |
|
12 |
- |
Headlamp High Switch_input |
- |
- |
Bumper Antenna Power_output |
|
13 |
Static Bending RH_output |
ACC_input |
- |
Heated handle switch_input |
- |
|
14 |
GND ECU |
IGN2_input |
Safety Power Window Enable_output |
Rear left seat belt switch_output |
- |
|
15 |
Heated handle power_output |
- |
- |
Rear right seat belt indicator_output |
- |
|
16 |
IGN2_Heated handle power |
PDW Power_input |
Front wiper low relay_output |
Rear center seat belt switch_output |
- |
|
17 |
|
Turn Signal FR LH_output |
Front wiper high relay_output |
|
Wheel Speed Sensor_input |
|
18 |
Turn Signal RR LH_output |
- |
- |
- |
|
|
19 |
- |
- |
Rear center seat belt indicator_output |
- |
|
|
20 |
- |
- |
- |
- |
|
|
21 |
- |
- |
- |
- |
|
|
22 |
- |
External Buzzer_output |
- |
IGN2 Relay_output |
|
|
23 |
- |
- |
|
ESCL (+)_output |
|
|
24 |
IGN 1_input |
Multi function switch GND_input |
ESCL enable_output |
||
|
25 |
Room lamp _output |
Rear right seat belt switch_input |
Starter feedback_input |
||
|
26 |
- |
Immobilizer Power_output |
Driver Outside handle_output |
||
|
27 |
PDW-R switch_input |
Immobilizer GND_output |
Passenger Outside handle_output |
||
|
28 |
Turn signal actuator_output |
AV Tail_output |
Passenger Outside handle antenna (-)_output |
||
|
29 |
- |
- |
Interior antenna 1 GND_output |
||
|
30 |
PDW-R indicator_input |
- |
Interior antenna 2 GND_output |
||
|
31 |
Autolight sensor GND_output |
Alatm Horn Relay_output |
Driver Outside handle antenna (-)_output |
||
|
32 |
Autolight sensor signal_output |
ESCL COM |
Bumper antenna GND_output |
||
|
33 |
Autolight sensor power_output |
- |
- |
||
|
34 |
LIN |
Rear wiper relay_output |
- |
||
|
35 |
B-CAN (Low) |
C-CAN (High) |
- |
||
|
36 |
B-CAN (High) |
C-CAN (Low) |
- |
||
|
37 |
Turn Signal RR RH_output |
|
- |
||
|
38 |
Turn Signal FR RH_output |
|
Smart Key Smart Key Code Saving 1. Connect the DLC cable of GDS to the data link connector (16 pins) in driver side crash pad lower panel, turn the power on GDS.
Circuit Diagram
Description The PTC (Positive Temperature Coefficient) heater is installed at the exit or the backside of heater core. The PTC heater is an electric heater using a PTC element as an auxiliary heating device that supplements deficiency of interior heat source in highly effective diesel engine.
Description Rear view camera will activate when the backup light is ON with the ignition switch ON and the shift lever in the R position. This system is a supplemental system that shows behind the vehicle through the AV monitor or the ECM (Reverse Display Room Mirror) mirror while backing-up.