Hyundai Venue: Brake Line / Repair procedures
Brake Hose
1. |
Turn ignition switch OFF and disconnect the negative (-) battery cable.
|
2. |
Disconnect the brake fluid level sensor connector (A).

|
3. |
Remove the brake fluid from the master cylinder reservoir with a syringe.
•
|
Do not spill brake fluid on the vehicle, it may damage
the paint; if brake fluid does contact the paint, wash
it off immediately with water.
|
•
|
Make sure no dirt or other foreign matter is allowed
to contaminate the brake fluid.
|
|
|
4. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
|
5. |
Remove the front wheel and tire (A) from front hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
|
•
|
Be careful not to damage the hub bolts when removing
the front wheel and tire (A).
|
|

|
6. |
Remove the brake hose clip (A).
|
7. |
Remove the tube flare nut (B).
Tightening torque :
12.7 - 16.7 N.m (1.3 - 1.7 kgf.m, 9.4 - 12.3 lb-ft)
|

|
8. |
Remove the brake caliper hose bracket bolt (A).
Tightening torque :
12.7 - 16.7 N.m (1.3 - 1.7 kgf.m, 9.4 - 12.3 lb-ft)
|

|
9. |
Remove the hose after loosening the brake hose bolt (A) from the caliper.
Tightening torque :
24.5 - 29.4 N.m (2.5 - 3.0 kgf.m, 18.1 - 21.7 lb-ft)
|

|
1. |
Turn ignition switch OFF and disconnect the negative (-) battery cable.
|
2. |
Disconnect the brake fluid level sensor connector (A).

|
3. |
Remove the brake fluid from the master cylinder reservoir with a syringe.
•
|
Do not spill brake fluid on the vehicle, it may damage
the paint; if brake fluid does contact the paint, wash
it off immediately with water.
|
•
|
Make sure no dirt or other foreign matter is allowed
to contaminate the brake fluid.
|
|
|
4. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
|
5. |
Remove the rear wheel and tire (A) from the rear hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
|
•
|
Be careful not to damage the hub bolts when removing
the rear wheel and tire (A).
|
|

|
6. |
Remove the tube flare nut (A).
|
7. |
Loosen the brake hose bracket bolt (B).
Tightening torque
(A) : 13.7 - 16.7 N.m (1.4 - 1.7 kgf.m, 10.1 - 12.3 lb-ft)
(B) : 7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 7.8 - 11.8 lb-ft)
|

|
8. |
Remove the tube flare nut (A).
|
9. |
Remove the hose after loosening the brake hose bolt (B) from the rear
drum brake.
Tightening torque
(A) : 13.7 - 16.7 N.m (1.4 - 1.7 kgf.m, 10.1 - 12.3 lb-ft)
(B) : 7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 7.8 - 11.8 lb-ft)
|

|
1. |
Turn ignition switch OFF and disconnect the negative (-) battery cable.
|
2. |
Disconnect the brake fluid level sensor connector (A).

|
3. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
|
4. |
Remove the rear wheel and tire (A) from the rear hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
|
•
|
Be careful not to damage the hub bolts when removing
the rear wheel and tire (A).
|
|

|
5. |
Remove the brake hose clip (A).
|
6. |
Remove the tube flare nut (B).
Tightening torque
12.7 - 16.7 N.m (1.3 - 1.7 kgf.m, 9.4 - 12.3 lb-ft)
|

|
7. |
Remove the hose after loosening the brake hose bolt (A) from the caliper.
Tightening torque
24.5 - 29.4 N.m (2.5 - 3.0 kgf.m, 18.1 - 21.7 lb-ft)
|

|
1. |
Check the brake tubes for cracks, crimps and corrosion.
|
2. |
Check the brake tube flare nuts for damage and fluid leakage.
|
1. |
To install, reverse the removal procedures.
•
|
Use a new washer (A) whenever installing.
[Front]

[Rear]

|
|
|
2. |
After installation, bleed the brake system.
(Refer to Brake System - "Brake Bleeding Prcoedures")
|
3. |
Check the brake oil leakage and pedal operating condition.
|
Other information:
To use the sunvisor, pull it downward.
To use the sunvisor to block the sun from the side window, pull it downward,
release it from the bracket (1) and swing it to the side (2) towards the window.
To use the vanity mirror, pull down the sunvisor and slide the mirror cover (3)...
..
Categories
Seat belt warning light (for driver’s seat)

As a reminder to the driver, the seat belt warning light will illuminate for
approximately 6 seconds each time you place the ignition switch to the ON position
regardless of belt fastening. However, if the seat belt is unfasted, a warning chime
will sound for approximately 6 seconds.
read more