Hyundai Venue: Cowl Top Cover / Components and components location

Hyundai Venue (QX) (2020-2025) Service Manual / Body (Interior and Exterior) / Cowl Top Cover / Components and components location

Component Location

Hyundai Venue. Components and components location

1. Cowl top cover

Repair procedures

Replacement 1. Remove the plug hole (A), loosen the mounting nuts and remove the wiper arm (B). Tightening torque : 22...

Other information:

Hyundai Venue (QX) (2020-2025) Service Manual: Transaxle Control Module (TCM). Schematic diagrams

TCM Connector Connector [A] Pin Description 2 35R clutch control solenoid valve (35R/C_VFS) 4 26 brake control solenoid valve (26/B_VFS) 5 Underdrive brake control solenoid valve (UD/B_VFS) 8 Inhibitor switch signal S2 (R) 19 Line pressure control solenoid valve (LINE_VFS) 21 Input speed sensor power 22 Output speed sensor power 32 Torque converter control solenoid valve (T/CON_VFS) 33 VB (Battery voltage) 34 Solenoid supply power 2 37 Output speed sensor signal 38 Inhibitor switch signal S4 (D) 39 Inhibitor switch signal S1 (P) 40 Manual mode up shift 42 Manual mode select switch 43 Oil temperature sensor (+) 45 VB (Battery voltage) 46 ON/OFF solenoid valve A(SS-A) 47 Overdrive clutch control solenoid valve (OD/C_VFS) 48 VB (Battery voltage) 49 Solenoid supply power 1 52 Input speed sensor signal 54 Inhibitor switch signal S3 (N) 57 Manual mode down shift 58 Oil temperature sensor (-) TCM Terminal input/ output signal Connector [A] Pin Description Condition Input/output value Type Level 2 35R clutch control solenoid valve (35R/C_VFS) - Output 0V/Battery voltage level 9V < Battery voltage level < 16V 4 26 brake control solenoid valve (26/B_VFS) - Output 0V/Battery voltage level 9V < Battery voltage level < 16V 5 Underdrive brake control solenoid valve (UD/B_VFS) - Output 0V/Battery voltage level 9V < Battery voltage level < 16V 8 Inhibitor switch signal S2 (R) High Input 0V/Battery voltage level Low 9V < Battery voltage level < 16V 19 Line pressure control solenoid valve (LINE_VFS) - Output 0V/Battery voltage level 9V < Battery voltage level < 16V 21 Input speed sensor power ON Power 0V/9V OFF 22 Output speed sensor power ON Power 0V/9V OFF 32 Torque converter control solenoid valve (T/CON_VFS) - Output 0V/Battery voltage level 9V < Battery voltage level < 16V 34 Solenoid power 2 Power 0V/Battery voltage level 9V < Battery voltage level < 16V 37 Output speed sensor signal High Input 0...

Hyundai Venue (QX) (2020-2025) Service Manual: General information

Tightening Torque Table of Standard Parts BOLT (Nominal diameter) NUT (Nominal diameter) BOLT/NUT Normal screw Torque Nm (kg.m, Ib-ft) Nominal diameter...

Categories

Air bag collision sensors

WARNING

To reduce the risk of an air bag deploying unexpectedly and causing serious injury or death:

Do not hit or allow any objects to impact the locations where air bags or sensors are installed. Do not perform maintenance on or around the air bag sensors. If the location or angle of the sensors is altered, the air bags may deploy when they should not or may not deploy when they should. Do not install bumper guards or replace the bumper with a nongenuine HYUNDAI parts. This may adversely affect the collision and air bag deployment performance. Place the ignition switch in the LOCK/OFF or ACC position when the vehicle is being towed to prevent inadvertent air bag deployment. Have all air bag repairs conducted by an authorized HYUNDAI dealer.

Hyundai Venue. Air bag collision sensors