Hyundai Venue (QX): Seat Electrical / Air Ventilation Seat. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Body Electrical System / Seat Electrical / Air Ventilation Seat. Repair procedures

Removal

[Ventilation Blower]

1.	Disconnect the negative (-) battery terminal.

2.	Remove the front seat. (Refer to Body - "Front Seat Assembly")

3.	Remove the blower duct (A).

4.	Remove the blower FAN (A) after removing the screws.

[Ventilation Seat Unit]

1.	Disconnect the negative (-) battery terminal.

2.	Remove the front seat. (Refer to Body - "Front seat Assembly")

3.	Remove the ventilation seat unit (A) after disconnect the connectors (B).

Installation

[Ventilation Blower]

1.	Install the blower fan.

2.	Install the duct.

3.	Install the front seat assembly.

4.	Connect the negative (-) battery terminal.

[Ventilation Seat Unit]

1.	Install the ventilation seat unit.

2.	Install the front seat assembly.

3.	Connect the negative (-) battery terminal.

Inspection

Ventilating seat consists of three units : the ventilating seat unit for control, switch for input and and blower for output.

Diagnosis Mode

1.	You can enter the diagnosis mode by turning the heater seat button on.

2.	You can enter the diagnosis mode by referring to following description.

Press the heating wire switch as shown below.

1)	Press and hold the heating wire switch for 3 seconds or more.

2)	Release the switch for 3 seconds or less and press and hold it again for 1.5 - 3 seconds.

3)	Release the switch for 3 seconds or less and press and hold it again for 3 seconds or more.

Hyundai Venue. Air Ventilation Seat. Repair procedures

When the vehicle enters the diagnostic mode, the three LEDs (Low, Mid, High) in the heating wire section blinks once for 0.5 seconds.

1)	When the vehicle enters the self-diagnostic mode, LEDs only work as those for heating wire seat switches.

2)	When two or more errors are detected, the LEDs sequentially blink at a 2-second interval for each error code.

Hyundai Venue. Air Ventilation Seat. Repair procedures

After entering the diagnostic mode, check the LED status to identify the error.

Hyundai Venue. Air Ventilation Seat. Repair procedures

Failure Indicator

LED (Flashing)

Inspection Items

Detailed Inspections

Hyundai Venue. Air Ventilation Seat. Repair procedures

Low voltage detection

Low voltage that deviates from the operating voltage range was supplied.

Over voltage detection

Overvoltage that deviates from the operating voltage range was supplied.

Hyundai Venue. Air Ventilation Seat. Repair procedures

Fuse (Short)

B+ fuse disconnection

IGN2 fuse disconnection

Hyundai Venue. Air Ventilation Seat. Repair procedures

NTC/HEATER MAT (Short)

1)	NTC element failure

2)	Heater mat disconnection

3)	Heater+ wiring disconnection

4)	Heater system NTC disconnection (4.9 V or higher)

Hyundai Venue. Air Ventilation Seat. Repair procedures

NTC/HEATER MAT (Disconnector)

1)	Short-circuit between the controller connector terminal and NTC

2)	Short-circuit between the controller connector terminal and heater

3)	Short-circuit in the heater system NTC wiring

4)	Short-circuit in the heater system heater+ wiring

Hyundai Venue. Air Ventilation Seat. Repair procedures

Target temperature not reached

Target temperature not reached within 40 minutes

Hyundai Venue. Air Ventilation Seat. Repair procedures

Short circuit of Ventilation blower power line

Short circuit of ventilation blower power line (short)

Hyundai Venue. Air Ventilation Seat. Repair procedures

Power disconnection of ventilation blower

Disconnection or missing connector of ventilation power line

Hyundai Venue. Air Ventilation Seat. Repair procedures

Short circuit of ventilation blower speed signal

Short circuit of ventilation blower speed signal (short)

Hyundai Venue. Air Ventilation Seat. Repair procedures

Disconnection or missing connector of ventilation blower speed signal

Disconnection or missing connector of ventilation blower speed signal (VCC)

Hyundai Venue. Air Ventilation Seat. Repair procedures

Disconnection or missing connector of ventilation blower speed signal

Disconnection or missing connector of ventilation blower speed signal (GND)

Hyundai Venue. Air Ventilation Seat. Repair procedures

Short circuit of ventilation blower RPM signal (short)

Hyundai Venue. Air Ventilation Seat. Repair procedures

Disconnection or missing connector of ventilation blower RPM signal

Disconnection or missing connector of ventilation blower RPM signal (GND)

Hyundai Venue. Air Ventilation Seat. Repair procedures

Disconnection or missing connector of ventilation blower RPM signal

Disconnection or missing connector of ventilation blower RPM signal (GND)

6.	You can check the malfunctioning by checking the blinking LED.

7.	The failure data is recorded to the memory by the ventilation seat unit.

8.	Press the heating wire seat switch on the passenger side for 5 seconds or more to make the LED blink four times and delete the failure data in the memory.

9.	Pressing the IGN OFF button will end the diagnosis mode for the heater seat.

10.	You can check whether the heating seat system works properly after turning the IGN ON. If you want to check the error code, you can refer to the procedure of 2 above.

❮Air Ventilation Seat. Schematic diagrams

Circuit Diagram N Connector A Connector B Connector C 1 Ventilation seat unit IGN1 Driver ventilation indicator(low) Ventilation heater power 2 Driver blower power Driver ventilation indicator(mid) Driver heater power 3 Driver blower speed Driver ventilation indicator(high) Driver heater ground 4 Driver RPM input Dirver NTC (+) Ventilation heater groung 5 Driver heater switch - Ventilation heater power 6 Driver ventilation switch ILL (-) - 7 ILL (+) Driver NTC (-) Passenger heater power 8 Driver heater indicator(low) Driver blower ground - 9 Driver heater indicator(mid) Passenger ventilation indicator(low) Passenger heater ground 10 Driver heater indicator(high) Passenger ventilation indicator(mid) Ventilation heater groung 11 Ventilation unit IGN2 Passenger ventilation indicator(high) 12 Passenger blower power Passenger NTC (+) 13 Passenger blower speed - 14 Passenger blower RPM input - 15 Passenger heater switch Passenger NTC (-) 16 Passenger ventilation switch Passenger blower ground 17 Detent 18 Passenger heater indicator(low) 19 Passenger heater indicator(mid) 20 Passenger heater indicator(high)

Lumber Support Units. Repair procedures❯

Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the front seat assembly.

Other information:

Hyundai Venue (QX) (2020-2026) Service Manual: Refrigerant Line. Repair procedures

Replacement 1. If the compressor is marginally operable, run the engine at idle speed, and let the air conditioning work for a few minutes, then shut the engine off. 2. Disconnect the negative (-) battery terminal.

Hyundai Venue (QX) (2020-2026) Service Manual: Description and operation

Description Rear Corner Radar is a system that measures the relative speed and distance from the following vehicles by using two electromagnetic wave radar sensors attached to the rear bumper, and detects any vehicle within the blind spot zone and gives off alarm.

Hyundai Venue (QX): Seat Electrical / Air Ventilation Seat. Repair procedures

Other information:

Hyundai Venue (QX) (2020-2026) Service Manual: Refrigerant Line. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual: Description and operation

Categories