Hyundai Venue (QX): Cooling System / Cooling Fan. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Engine Mechanical System / Cooling System / Cooling Fan. Repair procedures

Removal and Installation
Cooling Fan Assembly
1.
Disconnect the battery negative terminal.
2.
Remove the air duct.
(Refer to Intake and Exhaust System - "Air Cleaner")
3.
Disconnect the over flow hose (A).

Hyundai Venue. Cooling Fan. Repair procedures
4.
Disconnect the radiator upper hose (A) and then remove the filler neck assembly (B).
Tightening torque:
7.8 - 11.8 Nm (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)

Hyundai Venue. Cooling Fan. Repair procedures
5.
Disconnect the wiring harness connector (A).

Hyundai Venue. Cooling Fan. Repair procedures
6.
Remove the front bumper.
(Refer to Body (Interior and Exterior) - "Front Bumper")
7.
Remove the intake shield (A).
Tightening torque:
7.8 - 11.8 Nm (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)

Hyundai Venue. Cooling Fan. Repair procedures
8.
Remove the radiator upper mounting bracket (A).
Tightening torque :
7.8 - 11.8 Nm (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)
[LH]

Hyundai Venue. Cooling Fan. Repair procedures

[RH]

Hyundai Venue. Cooling Fan. Repair procedures
9.
Remove the front bumper beam.
(Refer to Body (Interior and Exterior) - "Front Bumper Beam Assembly")
10.
Disconnect the ATF cooler hoses (A).

Hyundai Venue. Cooling Fan. Repair procedures
11.
Remove the cooling fan (A) from the radiator.

Hyundai Venue. Cooling Fan. Repair procedures
12.
Install in the reverse order of removal.
13.
Fill with engine coolant.
(Refer to Cooling System - "Coolant")
Hyundai Venue. Cooling Fan. Repair procedures   
•
The coolant must be injected according to the integrated thermal management module (ITM) coolant filling method.
Resistor
1.
Disconnect the battery terminals.
2.
Disconnect the wire harness connector (A) and fan motor connector (B).

Hyundai Venue. Cooling Fan. Repair procedures
3.
Remove the resistor (A) from fan shroud.
Tightening torque :
1.7 - 2.4 (0.18 - 0.25 kgf.m, 1.3 - 1.8 lb-ft)

Hyundai Venue. Cooling Fan. Repair procedures
4.
Install in the reverse order of removal.
Disassembly
1.
Remove the cooling fan (A) from the cooling fan shroud.
Tightening torque :
2.8 - 3.2 N.m (0.28 - 0.33 kgf.m, 2.1 - 2.4 lb-ft)

Hyundai Venue. Cooling Fan. Repair procedures
2.
Disconnect the fan motor connector (A) from the resistor.
3.
Loosen the screws and then remove the fan motor (B) from the cooling fan shroud.
Tightening torque :
3.9 - 5.8 N.m (0.4 - 0.6 kgf.m, 2.8 - 4.3 lb-ft)

Hyundai Venue. Cooling Fan. Repair procedures
4.
Assemble in the reverse order of disassembly.

    Components 1. Resister 2. Cooling fan 3. Cooling fan motor 4. Cooling fan shroud 5. Reservoir tank

    Removal and Installation    • Never remove the radiator cap when the engine is hot.

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Repair procedures

    Inspection 1. Disconnect the ignition switch connector (B) and key warning switch connector (A) from under the steering column. 2. Check for continuity between the terminals. 3.

    Hyundai Venue (QX) (2020-2026) Service Manual: Repair procedures

    Refrigerant System Service Basics (R-134a) Refrigerant Recovery Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a(R-134a) from the air conditioning system.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.014