Hyundai Venue (QX): Blower / Intake Actuator. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Heating, Ventilation and Air Conditioning / Blower / Intake Actuator. Repair procedures

Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the intake actuator connector.
3.
Verify that the intake actuator operates to the fresh position when connecting 12V to terminal 3 and grounding terminal 4.
Verify that the intake actuator operates to the recirculation position when connected in reverse.

Hyundai Venue. Intake Actuator. Repair procedures

1. -
2. -
3. Fresh air
4. Recirculated air
 5. Sensor (+ 5V)
6. Feedback signal
7. Sensor ground

4.
Connect the intake actuator connector.
5.
Turn the ignition switch ON.
6.
Check the voltage between terminal 6 and 5.
Hyundai Venue. Intake Actuator. Repair procedures   
•
It will feedback the current position of the actuator to controls.
Specification
Door position
Voltage (V)
Error detecting
Fresh air
 0.5 ± 0.15
 Low voltage : 0.1V or less
Recirculated air
 4.5 ± 0.15
 High voltage : 4.9V or more

7.
If the intake actuator does not operate well, substitute with a known-good intake actuator and check for proper operation.
8.
Replace the intake actuator if it is proved that there is a problem with it.
Diagnosis With GDS
1.
The heating, ventilation and air conditioning can be quickly diagnosed failed parts with vehicle diagnostic system (GDS).
※ The diagnostic system (GDS) provides the following information.
(1) Self diagnosis : Checking the failure code (DTC) and display.
(2) Current data : Checking the system input/output data state.
(3) Actuation test : Checking the system operation condition.
(4) Additional function : Other controlling such as he system option and zero point adjustment.
2.
Select the 'Car model' and the system to be checked in order to check the vehicle with the tester.
3.
Select the 'Current data' menu to search the current state of the input / output data.
The input / output data for the sensors corresponding to the Intake Actuator can be checked.

Hyundai Venue. Intake Actuator. Repair procedures
4.
To perform compulsory operation on Intake Actuator input factors, select "ACTUATION TEST".

Hyundai Venue. Intake Actuator. Repair procedures
Replacement
1.
Disconnect the negative (-) battery terminal.
2.
Remove the main crash pad assembly.
(Refer to Body - "Main Crash Pad Assembly")
3.
Separate the connector (A) and loosen the mounting screws and remove the intake actuator (B).

Hyundai Venue. Intake Actuator. Repair procedures
4.
To install, reverse the removal procedure.
Hyundai Venue. Intake Actuator. Repair procedures   
•
Make sure the connector is connected in properly.
•
Replace any damaged clips.

    Description The intake actuator is located at the blower unit. It regulates the intake door by a signal from the control unit. Pressing the intake selection switch will shift between recirculation and fresh air modes.

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Troubleshooting

    Troubleshooting Problem Symptoms Table Before replacing or repairing air conditioning components, first determine if the malfunction is due to the refrigerant charge, air flow or compressor. Use the table below to help you find the cause of the problem.

    Hyundai Venue (QX) (2020-2026) Service Manual: PTC Heater. Description and operation

    Description The PTC (Positive Temperature Coefficient) heater is installed at the exit or the backside of heater core. The PTC heater is an electric heater using a PTC element as an auxiliary heating device that supplements deficiency of interior heat source in highly effective diesel engine.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0151