Hyundai Venue (QX): Airbag Module / Driver Airbag (DAB) Module and Clock Spring. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Restraint / Airbag Module / Driver Airbag (DAB) Module and Clock Spring. Repair procedures

Removal
1.
Disconnect the battery negative cable and wait for at least three minutes before beginning work.
2.
Remove the driver airbag module mounting bolts.

Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures
3.
Disconnect the DAB connector (A).

Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures
4.
Remove the steering wheel.
(Refer to Steering System - "Steering Wheel")
5.
Remove the steering wheel and steering wheel column shround
(Refer to Steering System - "Steering Column and Shaft")
6.
Remove the clock spring after disconnecting the clock spring connector (A).

Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures
Inspection
Driver Airbag (DAB)
If any improper parts are found during the following inspection, replace the airbag module with a new one.
Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures   
•
Never attempt to measure the circuit resistance of the airbag module (squib) even if you are using the specified tester. If the circuit resistance is measured with a tester, accidental airbag deployment will result in serious personal injury.
1.
Check pad cover for dents, cracks or deformities.
2.
Check the airbag module for denting, cracking or deformation.
3.
Check hooks and connectors for damage, terminals for deformities, and harness for binds.
4.
Check airbag inflator case for dents, cracks or deformities.

Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures
5.
Install the airbag module to the steering wheel to check for fit or alignment with the wheel.
Clock Spring
1.
If, as a result of the following checks, even one abnormal point is discovered, replace the clock spring with a new one.
2.
Check connectors and clock spring for damage, and terminals for deformities.

Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures
Installation
1.
Set the front tires straight-ahead.
2.
Turn the ignition switch OFF.
3.
Disconnect the battery negative cable from the battery and wait for at least three minutes before beginning the work.
4.
Connect the clock spring harness connector and horn harness connector to the clock spring.
5.
Clock spring manual neutral setting procedure.
(1)
Turn the clock spring clockwise until it stops.

Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures
(2)
Turn counter-clockwise 3 rotations and then align the neutral mark ( ▶◀ ).

Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures
6.
Install the steering wheel column shroud and the steering wheel.
(Refer to Steering System - "Steering Column and Shaft")
7.
Connect the Driver Airbag (DAB) module connector and horn connector, and then install the Driver Airbag (DAB) module on the steering wheel.
Tightening torque :
7.8 - 10.8 N.m (0.8 - 1.1 kgf.m, 5.8 - 8.0 Ib-ft)
Hyundai Venue. Driver Airbag (DAB) Module and Clock Spring. Repair procedures   
•
.When install the Driver Airbag (DAB) module, Fix the horn wire and DAB inflator wire tightly with wire clip.
8.
Connect the battery negative cable.
9.
After installing the airbag, confirm proper system operation :
•
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
•
Make sure horn button works.

    Components 1. Driver Air Bag (DAB) 2. Steering Wheel 3. Clock Spring

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: A/C Pressure Transducer. Description and operation

    Description The A/C Pressure Transducer (APT) converts the pressure value of high pressure line into voltage value after measuring it. By converted voltage value, engine ECU controls the cooling fan by operating it high speed or low speed.

    Hyundai Venue (QX) (2020-2026) Service Manual: PTC Heater. Repair procedures

    Inspection Operating Logic Test (Manual only) Inspect the PTC operation by confirmation logic as follows; 1. Entering (1) Set the Floor mode and maximum heating position. (2) Turn off the blower switch.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0108