Hyundai Venue (QX): Power Door Mirrors / Power Door Mirror Assembly. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Body Electrical System / Power Door Mirrors / Power Door Mirror Assembly. Repair procedures

Inspection

1.	Disconnect the negative (-) battery terminal.

2.	Remove the door trim. (Refer to Body - "Front Door Trim")

3.	Disconnect the power door mirror connector (A) from the harness.

4.	Apply battery voltage to each terminal as shown in the table and verify that the mirror operates properly. Actuator Folding Mirroe Side repeater lamp/Mirror heater Warning indicator

Removal

1.	Disconnect (-) battery terminal.

Using a fastener remover (C), remove the mirror (A) as illustration below.

Hyundai Venue. Power Door Mirror Assembly. Repair procedures

•	Protect mirror from removing tool with cloth (B) wrapped.

•	Be careful not to damage mirror and mirror housing during removing process.

•	Apply force around the center of mirror because to apply force the end of mirror will break it.

3.	Disconnect the mirror connector (A).

Remove the scalp.

(1)	Attach protection tape at the end of the screw driver.

(2)

Insert screw driver in where you can see the back of scalp.

Hyundai Venue. Power Door Mirror Assembly. Repair procedures

•	When inserting screw driver, avoid to touch internal wires in the mirror housing.

(3)

Hold the mirror assembly with one hand and hold the screwdriver with the other hand and strike it vertically as shown illustration below.

Hyundai Venue. Power Door Mirror Assembly. Repair procedures

•	It is the way that screw driver strikes inner side of scalp cover to remove.

•	Lift screw driver and door mirror assembly about 20cm height from floor then smash them vertically.

•	scalp is thrown and removed because screw driver push the back of scalp cover to remove.

•	After removing the scalp, make sure that the clip and hook on the back of the scalp are not damaged.

•	If clips and hooks are damaged, replace the scalp with a new one as noise may occur in driving.

5.	Remove the front housing cover (A).

Disconnect the LED side repeater lamp connector (A) and then remove the LED side repeater lamp (B).

Hyundai Venue. Power Door Mirror Assembly. Repair procedures

•	Be careful not to damage the LED side repeater lamp fixing hook

Installation

1.	Install the puddle lamp and LED side repeater lamp.

2.	Install the front housing cover.

Install the scalp.

•	Install the scalp in the vertical direction that the inner fixing hook is not damaged.

•	When scalp installing, install the folded area first and then the far area.

•	Pushing the around of scalp with both hands and then make sure that it is completely installed.

4.	Install the door mirror assembly.

5.	Connect (-) battery terminal then check if door mirror lamp works normally.

❮Power Door Mirror Assembly. Components and components location

Components 1. Side repeater lamp 2. Warning indicator

Power Windows❯

Other information:

Hyundai Venue (QX) (2020-2026) Service Manual: PTC Heater. Description and operation

Description The PTC (Positive Temperature Coefficient) heater is installed at the exit or the backside of heater core. The PTC heater is an electric heater using a PTC element as an auxiliary heating device that supplements deficiency of interior heat source in highly effective diesel engine.

Hyundai Venue (QX) (2020-2026) Service Manual: Repair procedures

Variant Coding When you need variant coding: – Replace Front View Camera with a new one ※ EOL Variant Coding and calibration required for new replacement Front View Camera Variant Coding

Hyundai Venue (QX): Power Door Mirrors / Power Door Mirror Assembly. Repair procedures

Other information:

Hyundai Venue (QX) (2020-2026) Service Manual: PTC Heater. Description and operation

Hyundai Venue (QX) (2020-2026) Service Manual: Repair procedures

Categories