Hyundai Venue (QX): Automatic Transaxle Control System / Transaxle Oil Temperature Sensor. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Automatic Transaxle System\ / Automatic Transaxle Control System / Transaxle Oil Temperature Sensor. Repair procedures

Removal
Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures   
•
When Diagnostic Trouble Codes (DTC) is on, perform the following procedure to replace it.
•
Automatic transaxle is composed of delicate components. Be careful not to cause any damage on the component in the course of assembly and disassembly.
•
Maintain clean condition so that foreign substance does not get into the automatic transaxle.
•
Use a coated apron, latex gloves, and stainless tray to prevent foreign substance from getting into the transaxle.
•
Automatic transaxle fluid (ATF) can be reused. Collect it using a clean 10-liter beaker.
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the air cleaner and air duct.
(1)
Remove the air duct (A).

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
(2)
Disconnect the breather hose (B) and air intake hose (C).
(3)
Remove the air cleaner assembly (D).
Tightening torque :
Hose clamp bolt (C):
2.9 - 4.9 N.m (0.3 - 0.5 kgf.m, 2.1 - 3.6 lb-ft)
Air cleaner assembly bolts (D) :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.3 Ib-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
3.
Remove the battery (+) terminal (A).
Tightening torque :
7.8 - 9.8 N.m (0.8 - 1.0 kgf.m, 5.8 - 7.2 lb-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
4.
Remove the battery mounting bracket (A) and the battery (B).
Tightening torque :
9.0 - 14.0 N.m (0.9 - 1.4 kgf.m, 6.6 - 10.3 Ib-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
5.
Remove the ECM.
(1)
Disconnect the ECM connector (A).
(2)
Loosen the mounting bolts (B) and then removing the ECM bracket assembly.
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
6.
Remove the battery tray.
(1)
Loosen the mounting bolt (A) and then removing the battery (+) terminal bracket.
Tightening torque :
8.0 - 10.0 N.m (0.8 - 1.0 kgf.m, 5.9 - 7.4 lb-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
(2)
Loosen the bolts and then removing the battery tray (A).
Tightening torque :
8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 Ib-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
7.
Remove the drain plug (A) and drain the ATF totally and then reinstall the drain plug.

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures   
•
Replace the gasket before reinstalling the drain plug.
•
After the installation, start the engine and then check if there are any leakages from the drain plug.
8.
Remove the wiring mounting clip (A).
9.
Disconnect the air breather hose (B) from the valve body cover.
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
10.
Disconnect the hose (A) after removing the automatic transaxle fluid cooler hose clamp.

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures   
•
Carefully install the clamp not to damage the hose.
•
Install the clamp in a correct direction not to be interfered with other parts.
•
After the installation, start the engine and then check if there are any leakages from the hose.
11.
Remove the valve body cover (A).
Tightening torque :
11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures   
•
Replace the gasket (A) before reinstalling the valve body cover.

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
•
After the installation, start the engine and then check if there are any leakages from the valve body cover.
12.
Disconnect the oil temperature sensor and solenoid valve connector (A) from the valve body.
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures   
•
Check for the looseness, poor connection, bending, corrosion, contamination, deterioration, or damage before reinstalling the solenoid valve connector.
13.
Remove the valve body assembly (A).
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
14.
Disconnect the input & output speed sensor connector (A).

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
15.
Loosen the main connctor bolt (A).
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
16.
Disconnect the solenoid valve connector (A).

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
17.
Remove the solenoid valve connector mounting clip (A).

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
18.
Remove the solenoid valve connector (A) by pushing down from the transaxle.

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures   
•
Replace the O-Ring (A) before reinstalling solenoid valve connector.

Hyundai Venue. Transaxle Oil Temperature Sensor. Repair procedures
Installation
1.
To install, reverse the removal procedure.
2.
Check fluid level, after filling the automatic transaxle with fluid.
(Refer to Automatic Transaxle Syatem - "Automatic Transaxle Fluid (ATF)")

    Specifications ▷ Type : Negative Thermal Coefficient Type Temp.[(°C)°F] Resistance (Ω) Min Max (-40) -40 48153 45301 51006 (-20) -4.

    Description Input speed sensor is a vital unit that measures the rate of rotation of the input shaft inside the transaxle and delivers the readings to the TCM.

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Ambient Temperature Sensor. Repair procedures

    Inspection 1. Check the resistance of the ambient temperature sensor between terminals 1 and 2 whether it changes by changing the ambient temperature. 1. Ambient Sensor (+) 2.

    Hyundai Venue (QX) (2020-2026) Service Manual: Description and operation

    Description The cruise control system is engaged by the cruise "ON/OFF" main switch located on right of steering wheel column. The system has the capability to cruise, coast, accelerate and resume speed. It also has a safety interrupt, engaged upon depressing brake or shifting select lever.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0109