Hyundai Venue (QX): Lighting System / Turn Signal Lamp. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Body Electrical System / Lighting System / Turn Signal Lamp. Repair procedures

REMOVAL

Front Turn Signal Lamp

1.	Disconnect the negative (-) battery terminal.

2.	Disconnect the turn signal lamp connector (A).

3.	Remove the turn signal lamp (A) after loosening mounting bolts.

4.	Replace the head lamp bulb after turning the bulb socket counterclockwise.

Door Mirror Side Repeater Lamp

1.	Disconnect (-) battery terminal.

Using a fastener remover (C), remove the mirror (A) as illustration below.

Hyundai Venue. Turn Signal Lamp. Repair procedures

•	Protect mirror from removing tool with cloth (B) wrapped.

•	Be careful not to damage mirror and mirror housing during removing process.

•	Apply force around the center of mirror because to apply force the end of mirror will break it.

Remove the scalp.

(1)	Attach protection tape at the end of the screw driver.

(2)

Insert screw driver in where you can see the back of scalp.

Hyundai Venue. Turn Signal Lamp. Repair procedures

•	When inserting screw driver, avoid to touch internal wires in the mirror housing.

(3)

Hold the mirror assembly with one hand and hold the screwdriver with the other hand and strike it vertically as shown illustration below.

Hyundai Venue. Turn Signal Lamp. Repair procedures

•	It is the way that screw driver strikes inner side of scalp cover to remove.

•	Lift screw driver and door mirror assembly about 20cm height from floor then smash them vertically.

•	scalp is thrown and removed because screw driver push the back of scalp cover to remove.

•	After removing the scalp, make sure that the clip and hook on the back of the scalp are not damaged.

•	If clips and hooks are damaged, replace the scalp with a new one as noise may occur in driving.

4.	Remove the front housing cover.

Disconnect the LED side repeater lamp connector (A) and then remove the LED side repeater lamp (B).

Hyundai Venue. Turn Signal Lamp. Repair procedures

•	Be careful not to damage the LED side repeater lamp fixing hook

INSTALLATION

Front Turn Signal Lamp

1.	Connect the lamp connector after install the front turn signal lamp.

2.	Connect the negative (-) battery terminal.

Door Mirror Side Repeater Lamp

1.	Install the puddle lamp and LED side repeater lamp.

2.	Install the front housing cover.

Install the scalp.

•	Install the scalp in the vertical direction that the inner fixing hook is not damaged.

•	When scalp installing, install the folded area first and then the far area.

•	Pushing the around of scalp with both hands and then make sure that it is completely installed.

4.	Install the door mirror assembly.

5.	Connect (-) battery terminal then check if door mirror lamp works normally.

❮Overhead Console Lamp. Repair procedures

Removal 1. Disconnect the negative (-) battery terminal. 2. Disconnect the overhead console lamp lense (A).

Hazard Lamp Switch. Repair procedures❯

Replacement 1. Disconnect the negative (-) battery terminal. 2. Remove the center fascia panel.

Other information:

Hyundai Venue (QX) (2020-2026) Service Manual: A/C Pressure Transducer. Repair procedures

Inspection • Before measuring the pressure of the refriferant line, check whether the refrigerant amount is charged in accordance with the specified charging amount.

Hyundai Venue (QX) (2020-2026) Service Manual: Schematic diagrams

System Block Diagram Component Parts And Function Outline Component part Function Vehicle-speed sensor, ESP/ABS Control Module Converts vehicle speed to pulse. ECM Receives signals from sensor and control switches.

Hyundai Venue (QX): Lighting System / Turn Signal Lamp. Repair procedures

Other information:

Hyundai Venue (QX) (2020-2026) Service Manual: A/C Pressure Transducer. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual: Schematic diagrams

Categories