Hyundai Venue (QX): Hydraulic System / Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Automatic Transaxle System\ / Hydraulic System / Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures

Inspection
Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures   
•
Refer to the DTC manual for the check procedure.
Removal
Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures   
•
When the solenoid valve Diagnostic Trouble Codes (DTC) is on, perform the following procedure to replace it.
•
Automatic transaxle is composed of delicate components. Be careful not to cause any damage on the component in the course of assembly and disassembly.
•
Maintain clean condition so that foreign substance does not get into the automatic transaxle.
•
Use a coated apron, latex gloves, and stainless tray to prevent foreign substance from getting into the transaxle.
•
Automatic transaxle fluid (ATF) can be reused. Collect it using a clean 10-liter beaker.
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the air cleaner and air duct.
(1)
Remove the air duct (A).

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
(2)
Disconnect the breather hose (B) and air intake hose (C).
(3)
Remove the air cleaner assembly (D).
Tightening torque :
Hose clamp bolt (C):
2.9 - 4.9 N.m (0.3 - 0.5 kgf.m, 2.1 - 3.6 lb-ft)
Air cleaner assembly bolts (D) :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.3 Ib-ft)

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
3.
Discharge the automatic transaxle fluid (ATF).
(Refer to Automatic Transaxle Syatem - "Automatic Transaxle Fluid (ATF)")
4.
Disconnect the wiring fixing clip (A).
5.
Disconnect the air bleeder hose (B).

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
6.
Disconnect the ATF cooler hose (A).

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures   
•
Be careful not to cause any damage on the hose when tightening the clamp.
•
Mount the clamp tightening part in the designated direction so that interference does not occur with the adjacent parts.
•
After connecting the hose, check for oil leakage on the connecting part while the engine is on.
7.
Unscrew the bolts and remove the valve body cover (A).
Tightening torque :
11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures   
•
When re-mounting the valve body cover, replace the gasket with a new one.
•
After mounting the valve body cover, check for oil leakage on the connecting part while the engine is on.

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
8.
Unscrew the bolts and disconnect the solenoid valve connector (A).

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
9.
Remove the support bracket mounting bolt (A).
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
10.
Remove the support bracket (A).
11.
Loosen the bolt (B).
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
12.
Remove the line pressure control solenoid valve (A).

Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
Installation
1.
To install, reverse the removal procedure.
2.
Inject the automatic transaxle oil and inspect the oil level.
(Refer to Automatic Transaxle System - "Automatic Transaxle Fluid (ATF)")
Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures   
1)
After ATF level check or exchange, be sure to remove residual ATF on transaxle case.
(Be especially sure to remove residual ATF between automatic transaxle case and valve body cover)
2)
After installing the valve body cover, make sure to check the oil leakage at the connection area with the engine ON.
3.
Clear the diagnostic trouble codes (DTC) using the diagnostic tool.
Hyundai Venue. Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures   
•
Even though disconnecting the battery negative terminal, the DTCs will not be cleared. So, be sure to clear the DTCs using the diagnostic tool.
4.
In order to prevent start delay and gear shift shock during acceleration and start, perform TCM learning after replacing the solenoid valve.
(Refer to Automatic Transaxle Control System - "Repair procedures")

    Component Location (1)_Valve Body Cover 1. Valve Body Cover 2. Valve Body Cover Gasket 3. Solenoid Valve Connector Component Location (2)_Solenoid Valve 1.

    Description • 35R Clutch control solenoid valve(35R/C) is attached to the valve body. • This variable force solenoid valve directly controls the hydraulic pressure inside the 35R clutch.

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Photo Sensor. Description and operation

    Description The photo sensor is located at the center of the defrost nozzles. The photo sensor contains a photovoltaic (sensitive to sunlight) diode. The solar radiation received by its light receiving portion, generates an electromotive force in proportion to the amount of radiation received which is transferred to th

    Hyundai Venue (QX) (2020-2026) Service Manual: Heater Unit. Repair procedures

    Replacement 1. Disconnect the negative (-) battery terminal. 2. Recover the refrigerant with a recovery / recycling / charging station. 3. When the engine is cool, drain the engine coolant from the radiator.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0248