Hyundai Venue (QX): Automatic Transaxle Control System / Shift Cable. Repair procedures

Hyundai Venue (QX) (2020-2026) Service Manual / Automatic Transaxle System\ / Automatic Transaxle Control System / Shift Cable. Repair procedures

Removal
1.
Turn OFF ignition switch and then diconnect the battery negative (-) cable.
2.
Remove the air cleaner and air duct.
(1)
Remove the air duct (A).

Hyundai Venue. Shift Cable. Repair procedures
(2)
Disconnect the breather hose (B) and air intake hose (C).
(3)
Remove the air cleaner assembly (D).
Tightening torque :
Hose clamp bolt (C):
2.9 - 4.9 N.m (0.3 - 0.5 kgf.m, 2.1 - 3.6 lb-ft)
Air cleaner assembly bolts (D) :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.3 Ib-ft)

Hyundai Venue. Shift Cable. Repair procedures
3.
Remove the battery (+) terminal (A).
Tightening torque :
7.8 - 9.8 N.m (0.8 - 1.0 kgf.m, 5.8 - 7.2 lb-ft)

Hyundai Venue. Shift Cable. Repair procedures
4.
Remove the battery mounting bracket (A) and the battery (B).
Tightening torque :
9.0 - 14.0 N.m (0.9 - 1.4 kgf.m, 6.6 - 10.3 Ib-ft)

Hyundai Venue. Shift Cable. Repair procedures
5.
Remove the ECM.
(1)
Disconnect the ECM connector (A).
(2)
Loosen the mounting bolts (B) and then removing the ECM bracket assembly.
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Shift Cable. Repair procedures
6.
Remove the battery tray.
(1)
Loosen the mounting bolt (A) and then removing the battery (+) terminal bracket.
Tightening torque :
8.0 - 10.0 N.m (0.8 - 1.0 kgf.m, 5.9 - 7.4 lb-ft)

Hyundai Venue. Shift Cable. Repair procedures
(2)
Loosen the bolts and then removing the battery tray (A).
Tightening torque :
8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 Ib-ft)

Hyundai Venue. Shift Cable. Repair procedures
7.
Remove the nut (A) from the manual control lever.
8.
Remove the shift cable (B) from the bracket (C) at transaxle side.

Hyundai Venue. Shift Cable. Repair procedures
9.
Remove the shift knob & boots (A).

Hyundai Venue. Shift Cable. Repair procedures
10.
Remove the floor console assembly.
(Refer to Body - "Floor Consol")
11.
Disconnect the connector (A).

Hyundai Venue. Shift Cable. Repair procedures
12.
Separate the air duct (A) from the both side.

Hyundai Venue. Shift Cable. Repair procedures
13.
Separate the shift cable.
(1)
Remove the snap pin (A).
(2)
Separate the shift cable (B).

Hyundai Venue. Shift Cable. Repair procedures
14.
Disconnect the shift cable retainer (A) after removing the nuts.
15.
Remove the shift cable by pulling it toward the interior.

Hyundai Venue. Shift Cable. Repair procedures
Installation
1.
Install the shift cable retainer (A).
Tightening torque :
11.8 - 14.7 N.m (1.2 - 1.5 kgf.m, 8.7 - 10.8 lb-ft)

Hyundai Venue. Shift Cable. Repair procedures

Hyundai Venue. Shift Cable. Repair procedures   
•
Install the cable after placing the shift lever and the manual control lever in the N position.
2.
Install the shift cable (A) in the shifter lever.

Hyundai Venue. Shift Cable. Repair procedures

Hyundai Venue. Shift Cable. Repair procedures   
•
Lug must assemble upward.

Hyundai Venue. Shift Cable. Repair procedures
•
When assembling the snap pin, be careful about the correct direction.
- The band portion (A) must point to the front of the vehicle.
- The band portion (A) must point outwards.

Hyundai Venue. Shift Cable. Repair procedures
3.
Install the air duct (A).

Hyundai Venue. Shift Cable. Repair procedures
4.
Install the shift knob & boots (A).

Hyundai Venue. Shift Cable. Repair procedures
5.
Install the shift cable (B) in the cable bracket (C).
6.
Align the hole (E) in the manual control lever with the "N" position hole (G) of the inhibitor switch and then insert the inhibitor switch guide pin (SST No: 09480-A3800).
7.
Lightly tighten the nut (A) after connected the shift cable (B) in the manual control lever (D).
8.
Tighten the nut (A) to the specified torque.
Tightening torque :
9.8 - 13.7 N.m (1.0 - 1.4 kgf.m, 7.2 - 10.1 lb-ft)

Hyundai Venue. Shift Cable. Repair procedures
9.
Remove the inhibitor switch guide pin (SST No.: 09480-A3800) from the hole.
10.
Install the battery tray.
(1)
Tighten the bolts and then install the battery tray (A).
Tightening torque :
8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 Ib-ft)

Hyundai Venue. Shift Cable. Repair procedures
(2)
Tighten the mounting bolt (A) and then install the battery (+) terminal bracket.
Tightening torque :
8.0 - 10.0 N.m (0.8 - 1.0 kgf.m, 5.9 - 7.4 lb-ft)

Hyundai Venue. Shift Cable. Repair procedures
11.
Install the ECM.
(1)
Connect the ECM connector (A).
(2)
Tighten the mounting bolts (B) and then install the ECM bracket assembly.
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Hyundai Venue. Shift Cable. Repair procedures
12.
Install the battery (B) and mounting bracket (A).
Tightening torque :
9.0 - 14.0 N.m (0.9 - 1.4 kgf.m, 6.6 - 10.3 Ib-ft)

Hyundai Venue. Shift Cable. Repair procedures
13.
Install the battery (+) terminal (A).
Tightening torque :
7.8 - 9.8 N.m (0.8 - 1.0 kgf.m, 5.8 - 7.2 lb-ft)

Hyundai Venue. Shift Cable. Repair procedures
14.
Install the air cleaner and air duct.
(1)
Install the breather hose (B) and air intake hose (C).
(2)
Install the air cleaner assembly (D).
Tightening torque :
Hose clamp bolt (C):
2.9 - 4.9 N.m (0.3 - 0.5 kgf.m, 2.1 - 3.6 lb-ft)
Air cleaner assembly bolts (D) :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.3 Ib-ft)

Hyundai Venue. Shift Cable. Repair procedures
(3)
Install the air duct (A).

Hyundai Venue. Shift Cable. Repair procedures
15.
Check that operating surely at each range of the inhibitor switch corresponding to each position of shift lever.

    Components Location 1. Shift lever knob & boots 2. Shift lever assembly 3. Shift cable 4. Manual control lever 5.

    Other information:

    Hyundai Venue (QX) (2020-2026) Service Manual: Rear Corner Radar Unit. Repair procedures

    Removal    lf replacement of the rear corner radar unit bracket or extension wire is required, replace the defective part only with a new one. 1.

    Hyundai Venue (QX) (2020-2026) Service Manual: Description and operation

    Description Rear view camera will activate when the backup light is ON with the ignition switch ON and the shift lever in the R position. This system is a supplemental system that shows behind the vehicle through the AV monitor or the ECM (Reverse Display Room Mirror) mirror while backing-up.

    Categories

     
    Copyright © 2026 www.hvenueqx.com - 0.0212